Marine Varnish
Marine Alternator And Generator Coil Varnish
Now available in convenient spray cans
"A True High Quality Phenolic Varnish Returns To The
Market"
UV proof - Salt spray proof - Water proof
After years of testing and formulation we have
re-discovered one of the worlds toughest marine grade coatings!
Green Marine Varnish is not an epoxy, urethane, enamel or
lacquer. Since our formula is based on high temperature Phenolic
coil varnishes used to coat magnetic field coils it can be
sprayed directly inside the alternator without fear of conductivity,
smoking, cracking and burning off when things get hot. Green
Marine Varnish is an excellent insulator of electricity so
make sure you do not coat the positive terminal post on the
back of the PMA. You will also have to keep a small metallic
spot clean for your negative ground bolt.
Best of all Green Marine Varnish is water proof and is absolutely
the best type of coating to stop corrosion on all metals!!!
Use Green Marine Varnish on all engine and mechanical parts
that need protecting from rust and corrosive environments.
Great for fan, pulleys, engine block, valve covers, pumps,
intake manifold, injector parts, drive shaft, transmission,
gear boxes, nuts and bolts etc. (Max temperature limit 800
degrees F. Not for use on exhaust manifolds unless they are
water cooled)
Use Green Marine Varnish anywhere you see rust or corrosion.
Spray it right over the damaged area. No need to clean area
before application. Clings to rusted or corroded areas and
instantly stops oxidation in it's tracks! Use multiple coats
to form an instant and long lasting protective barrier.
For wind turbines simply spray every part of it inside and
out with Green Marine Varnish and make it last a lifetime.
Great for protecting and even rejuvenating shorted and damaged
magnetic field coils! Great for use on all types of electric
generators inside and out! Protects corroded battery terminates
and cable. Can also be used to coat circuit boards and all
electronic parts from water and corrosion. A must have item
for protecting field coils from corrosion. Corrosion is the
#1 killer of all generators, alternators and all electronic
parts!!! Varnish can be sprayed directly inside alternator
bodies without the need for disassembling them!
High solvent formula has excellent mobility and easily flows
into intricate areas and if applied carefully will not bind
rotating parts together (Turn rotor occasionally during drying)
Green Marine Varnish is very high in solvents so it really
penetrates deep into metal surfaces creating a very tough
coating!!!
If you are old enough to remember, many of you may still recall
that spray paint made way back in the 1960's produced really
ultra tough coatings!!! As the years marched on many of the
chemicals that made the old spray paint formulas stick to
metal so well where slowly banned from use in all consumer
products BUT professionals could still have access to them!
Green Marine Varnish cannot be found on store shelves simply
because it contains so much high solvent chemistry.
Protect your PMA and Wind Turbine
Parts for the next 50 years with Green Marine Varnish.
For use on these metals:
- Aluminum
- Zinc
- Copper
- Brass
- Iron and steel
Green Marine Varnish is fast drying and can be safely handled
after 15 minutes but it takes 14 to 20 days to reach it's
full cure. To touch up any scratches caused by tools simply
re-coat affected areas. We suggest that any touch up coating
be done just before turbine is lifted into final position
on the pole. This assures plenty of uninterrupted drying time
providing for a long and durable coating. UV proof - Salt
spray proof.
Green Marine Varnish
- Sold in big 20oz. can
(One can will coat 6 PMA's or 2 complete Eagle wind turbines)
1 - 20oz. Cans
Only $49.95 #GMV2
--------------------------------------------------------
Clear Marine Varnish
(One can will coat 6 PMA's or 2 complete
Eagle wind turbines)
1 - 20oz.
Cans Only $49.95
#CMV2
Great for protecting or even rejuvenating shorted and damaged
magnetic field coils!
Use Green Marine Varnish on all engine and mechanical parts
that need protecting from rust and corrosive environments.
Great for fan, pulleys, block, valve covers, pumps, intake
manifold, injector parts, drive shaft, transmission, gear
boxes, nuts and bolts etc. For wind turbines simply spray
every part of it with Green Marine Varnish and make it last
a lifetime.
(Max temperature limit 800 degrees F. Not for use on exhaust
manifolds unless they are water cooled)
Great for use on all types of electric generators inside and
out!
- Avoid breathing fumes!!!
- Use ONLY in very well ventilated
area!!!
- Flammable. Keep far away from
fire and sparks when spraying!!!
Green/Clear Marine
Varnish is fast drying and can be safely handled after 15
minutes but it takes 7 to 14 days to reach it's full hardness
potential. Can also be oven baked at 275 degrees F. for
30 minutes for an instant cure.
WARNING: This product contains a chemical
known by the state of California to cause birth detects
or other reproductive harm.
EAGLE
WIND TURBINES BLADES
Sets 59" - 88"
PMA'S BRACKETS
PMA's - Std. Series
Super Core PMA's
|